In addition, washing in cold instead of hot water reduces wear on clothing but does not kill mould spores. As mould grows on the seals and drum of your equipment, you’ll begin to notice musty odours that can transfer to your clothing. To prevent mould and mildew from forming:
Don’t allow damp clothing to sit inside the machine. Remove them immediately after the wash cycle has been completed. Avoid washing before going to bed at night or before leaving for work in the morning, which would keep clothing in the machine for an extended period of time.
Improve air circulation in the machine and allow it to dry out by leaving the door and detergent dispenser open when not in use. Keep children and pets safe by locking the laundry room door.
Use liquid detergent instead of powder to reduce the build-up of residue. Also, use only the recommended amount of detergent to be sure it completely cycles through in the wash. More detergent will not make clothes cleaner.
If your laundry room or basement laundry area is damp, running a dehumidifier will help remove moisture from the air and reduce mould from growing.
The technology is very different from your traditional-style washing machine, so there are a few things that you must do differently or avoid altogether or risk damaging your equipment:
Don’t use regular detergents as they produce too many suds. Over time, a thick film can build up on the hoses and the drum, which may cause mechanical or electronic damage to the machine. To avoid receiving an Error Code F21 on a Maytag Washer, always use specially made, high-efficiency (HE) detergents that produce low suds. Read labels carefully, as using the wrong detergent can sometimes void the warranty.
Discontinue using fabric softener in the washer. Today’s detergents include a softener, so the extra liquid is not necessary. Consider using dryer sheets instead that reduce static without leaving a residue. One teaspoon will handle the entire load if you use a liquid fabric softener. The same goes for bleach—use one tablespoon of concentrated or two tablespoons of regular bleach for a full load.
One of the top reasons homeowners require appliance repair is to protect the door seal gasket (boot) with regular cleanings. Residue and debris from laundry can build up on the door seal. Sticky detergents will make the door harder to open and close; the seal will become misshapen and leak or tear. It’s also more prone to be a breeding ground for mould and mildew. Protect your investment by:
Combining a solution of half water and half vinegar to strip down and remove all fabric, pieces of hair and other debris. Use a cotton swab to reach into corners and hard-to-clean spots. Wipe out the inside of the drum also to eliminate odours.
If you notice mould growing on the seal, pull back the rubber lining and wipe it down (including all the creases in and around the lining) with bleach or mildew cleaners. Be sure to wear gloves and leave the door open for five minutes to allow fumes to circulate.
Regularly inspect the door seal, ensuring it fits snuggly against the machine. If you notice cracks, tears or receive an error code, contact a repair service to replace it.
It’s counterintuitive to think of the product that’s instrumental in cleaning your clothes, which can contribute to the mess. To ensure you’re receiving all the benefits detergents can provide and none of the drawbacks, it’s important to address issues with the cleaning dispenser and filter system.
To dry out the detergent dispenser drawer and reduce mould and mildew formation, you should leave the drawer out when you’re not using the machine.
The detergent will eventually build up residue in the drawer that may promote mould and mildew. To ensure this doesn’t transfer to clothing, you’ll want to clean your dispenser drawer thoroughly. About once a month (or more often if you do a lot of laundry), remove the drawer and carefully separate the compartments. Soak the parts for approximately 15-20 minutes in a sink full of water and 1/3 cup of white vinegar. Meanwhile, wipe down the inside compartment with a paper towel dipped in bleach. This will kill any mould spores lingering there. Now that the grime on the soaking compartments has loosened go back and scrub them clean. Allow to dry and place back inside the washer. The drawer is not dishwasher safe, so using this method will melt or warp the plastic.
As you might imagine, everything that builds up in the dispenser and filter can also cause a problem in your machine’s washtub. Most units have a special cycle designed specifically to clean the washtub. Running this once a month will remove all the unwanted detergent build-up and residue to keep your wash drum performing in top condition.
Empty the wash drum, add liquid chlorine bleach, powder cleaner or tub cleaner to the detergent dispenser. No detergent should be used at this time. Close the drawer and the door.
At the end of the cycle, allow the washer to cool down before opening the door. Then, wipe around the washer door opening, seal and glass with a towel to remove moisture.
If your machine doesn’t have a “Tub Clean” feature, follow the directions above but run the machine on the hottest cycle, plus an extra rinse.
Appliance Repair TorontoWhether your machine displays an Error Code or you notice problems with water drainage, excessive vibrations, longer than usual cycle times, wet clothes after the final spin, or strange pauses in the wash cycle, you may have a clogged drain pump filter. You can easily avoid or rectify this problem by cleaning the filter regularly.
To save on part wear and tear, always select the appropriate spin speed for the load you’re washing. Higher speeds will mean drier clothes but may potentially shorten the machine’s lifespan.
The drain pump filter located behind a small door at the bottom/front of your front-loading washing machine should be cleaned every few weeks. The role of the filter is to trap hair, lint, bits of fabric and other debris. To ensure your machine drains dirty water quickly, you’ll need to remove the filter and clean off these particles. You may want to use gloves and rinse the filter in clear water before putting it back into the machine.
If you’ve followed all the instructions and cared for your machine with regular cleaning and yet you still receive Maytag Washer Error Codes, you may be able to troubleshoot the problem yourself before calling in a repair technician. Check out our Easy DIY Diagnostics page to match your situation with the proper course of action. Write down any error codes or symptoms so that even if you cannot repair the problem yourself, the service tech can pinpoint the problem more quickly.
Do plan for wash cycles to be longer than traditional top-load cycles. Using less water saves money but requires extra time to clean the clothes. It also reduces dryer time as high spin speeds leave less water on clothing.
Do make sure you’ve removed all clothing after each load. Small items can easily become trapped in the basket, leading to mould and bacteria growth.
Do consider diluting liquid fabric softener with water (1:6) or eliminating it entirely. Commercial products are sticky and adhere to the door seal, detergent dispenser and interior drum. A pre-mixed, diluted bottle of fabric softener will help regulate use and reduce problems.
Do consider diluting liquid fabric softener with water (1:6) or eliminating it entirely. Commercial products are sticky and adhere to the door seal, detergent dispenser and interior drum. A pre-mixed, diluted bottle of fabric softener will help regulate use and reduce problems.
Don’t wash single items; the machine will sense an out-of-balance load and stop. Even if it does complete the cycle, the clothing will still be wet as the spin cycle will be ineffective.
Don’t leave loose change, keys or other items in your pockets during the wash cycle. This will lead to breakdowns and damage. Always check pockets before starting the wash.
One of the essential parts of any front-load washer is a rubber gasket. Let’s describe some important points in brief. A gasket seal is a watertight rubber serving to prevent water from flowing out of the washer during the cycle. The door exerts a compressive force on the rubber gasket, causing the gasket to deform elastically for a sealing effect.
When you have a leaky washing machine door seal, it can be a disaster. Water leaking may cause your clothes to get wet or water spills on the floor and needs to be cleaned up. Moreover, the other thing is the potential for mould and mildew to grow in places where water pools.
A door gasket is the most common reason for water leakage in any washing machine. They often acquire holes or tears, letting water leak down inside the washer machine, which leaks out from underneath. Still, they can also leak from the door itself straight down the front of the washer machine, or you may face such things as the washing machine leaking from the bottom that requires the aid of the experts.
If you’ve experienced any of the following and need to replace your door boot, be sure to contact us directly with the model number of your washer. Our washing machine experts can easily find the correct door boot for your washer model.
How often you should clean your washing machine door seal depends on how extensively you use your washing machine. Let’s point out the main signs when it is necessary to clean a door seal:
However, once you are having trouble cleaning your machine door seal, mould may have seeped into the rubber, and in this case, you should replace the seal.
First, mix 1 cup of bleach and 1 cup of baking soda (homemade cleaning solution) and pour into the detergent drawer. Then, add another cup of baking soda to the sealing area of the washing machine drum.
